Basic Gunnery – 14T Launcher Table IV Practice Test

These questions are part of the practice quiz. Start practicing

• When using the Aiming Circle, how far should the plumb bob's final position be above the stake?
• How long does "WAIT" display on the PBIT after powering up the ELES before the CDP displays the ELES status menu?
• What could be a potential consequence of not conducting regular cleaning on the 14T Launcher?
• What is a key safety consideration when using the GMT during reload operations?
• What type of maintenance is crucial after operating the 14T Launcher?
• How do you establish communication with the command center using the 14T?
• What does a line under a selected item from the CDP on an ELES LS indicate?
• What component provides synchronization and timing signals for VHF radio and fiber optic links?
• Which piece of equipment is critical for ensuring accurate readings in a firing system?
• What is the required distance for wearing hearing protection?
• Which of the following is essential for preventing overheating of the launcher’s electronic components?
• What should an operator be cautious of when using Patriot equipment?
• In what position must the ECH be placed and verified before placing the LS in Remote?
• What does INFS stand for?
• What is the role of simulations in training for the 14T Launcher?
• What is the role of the fire control system in the 14T Launcher?
• What is the output of a 15Kw Patriot Power generator?
• What does ELES stand for?
• What is the maximum weight for storing a 30-150lb torque wrench?
• Is a PAC2 GM able to move in the canister if the Torque Tube Handle is not properly locked?
• What must a CM5 do before unpacking and operating cranes for GMT reload?
• What is the minimum distance between launch stations (LSs)?
• What is the purpose of cautions noted in Patriot Technical Manuals (TMs)?
• What type of communication is essential during a launch?
• What is the primary component responsible for launching the missile in the 14T system?
• What is indicated by the term "INERT" on canisters?
• After how many miles of operation should lug nuts be torqued if a trailer is new or if wheels and tires have been removed?
• What is the primary function of the gunners quadrant in the emplacement process?
• How many control levers are present for the crane on the GMT?
• If one missile hazard light comes on and a live missile is present, what should be done?
• Which factor is NOT considered when choosing a missile for a specific target?
• During a PAC3 system check, what must be ensured before the test launch procedure?
• What is a key aspect of the maintenance process for the 14T Launcher?
• What does “target lock” mean in missile guidance?
• What should be included in the transport checklist for the 14T Launcher?
• When does time stop for the GMT reload process?
• Which of the following is true about the tilt warning alarm?
• What must be verified before transporting the 14T Launcher?
• What is the primary purpose of the circular level on the Aiming Circle?
• What is the correct sequence for initializing the Launcher control panel?
• What is the status of the Enable/Disable switch for each launcher when electrical power is applied?
• What is a crucial factor during the planning phase of a launch?
• What does the abbreviation TFOCA stand for?
• What equipment is necessary for manual emplacement?
• What position should the 5A2A4 Computer Select switch be set to?
• In what situation should the PAC3 Test Launch be canceled?
• What does the term 'visual serviceability inspection' imply?
• On the PAC3 LS, what component replaced the LMRD?
• To guide the driver, how far should you stand from the front roadside bumper of the vehicle at a minimum?
• What is a key indicator of a generator's readiness to operate?
• When off-loading empty canisters, how far must they be placed from the GMT?
• How can you confirm ECS has Local Status in electronic local on ELES?
• How long should you leave a berm after switching to remote?
• How does the operator ensure safe engagement of a target with the 14T?
• Which safety aspect is prioritized before closing the access door after generator operation?
• How far can the 10K forklift oscillate left or right in degrees?
• What is the normal operating level coolant temperature on a generator?
• Which gauge reading should be monitored for safe operation of the generator?
• Before placing LS in remote, what must CM3 receive?
• Why is precise targeting critical for the operation of the 14T Launcher?
• What does the acronym "TMS" stand for in the context of 14T operations?
• How deep should ground rods be installed?
• What does the abbreviation "NATO" stand for?
• How often should preventive maintenance checks be executed on the 14T Launcher?
• How many LS's can be linked in a daisy chain?
• What is the necessary torque for the GM tie down bolts?
• How many PMP windows are located on the CDP?
• What is the allotted time for preparing movement (PM) and emplacement (E) respectively?
• What is the first action after setting ELES Power to ON during the PAC3 Test Launch?
• How many faults or failures should occur in MRCTS tests to consider it valid?
• What critical data does the Launcher provide during active targeting?
• In what order are the GM torque tube handles locked?
• What must be confirmed regarding the fault lamps before closing the access door?
• What should the tractor oil pressure gauge read under normal conditions?
• How many times must MRCTS tests be performed to rule out intermittent problems?
• Which of the following is a recommended best practice for maintaining the 14T Launcher?
• What does the term "impact point" refer to in missile operations?
• What is an essential skill learned in the Basic Gunnery course for 14T personnel?
• What are the three settings for the ELES Power switch?
• When the circuit breaker lamp is on, which indication confirms the fault status?
• The crane operator should swing the boom slowly enough to have what?
• Which of the following is NOT checked during the verification process after the generator is completed?
• What must be done to J1 of each live PAC2 GM immediately after the cable connection is disconnected to eliminate static charge?
• What must be checked before executing a launch?
• What is the purpose of the ELES Power switch?
• What does the "Front" position on the 5A2A4 Computer Select switch indicate?
• When does the generator send a fuel state alert to the ECS?
• Identify one method of improving firing accuracy in the 14T Launcher.
• What is the procedure for ensuring the safety of personnel during launch?
• What kind of information does the Launch Table IV provide?
• What is the length of TFOCA mils?
• What is the normal oil pressure range for the HEMTT?
• What is the weight of a live PAC2 Guided Missile?
• What is the maximum weight the forklift can hold at maximum height?
• What indicates a successful initialization of the LS by the ECS?
• How should personnel respond to a potential threat during a launch?
• Which action is part of verifying the launcher's operational status?
• During live-fire operations, how is the Launch Table IV utilized?
• For M902 LS, what should be done after PMCS is completed?
• What does BITE stand for?
• Which component controls the missile launch process in the 14T system?
• Which factors can impact missile performance during an operation?
• Which TM is utilized for PMCS on the M902 LS?
• What can be inferred about the importance of following launch procedures?
• Which color air hose connects to the emergency coupling on a HEMTT?
• What is involved in conducting a post-fire analysis?
• What operations can be performed from the LS set-up on the CDP?
• What are "target coordinates," and why are they important?
• What could occur if launch procedures are not followed?
• What is a critical consideration when conducting built-in testing (like PBIT)?
• To which setting should the 5A2A4 Computer Select switch be adjusted?
• What is the base nomenclature for the GMT?
• What is the oil pressure range for a 15Kw generator?
• What role does the operator play in target acquisition?
• What is the typical distance between LS and GMT for parallel reload?
• How should misfires be handled in gunnery operations?
• How are PAC3 MRT canisters identified visually?
• What is the primary goal of the "Fire Mission" procedure in 14T operations?
• Which TM is utilized for performing PMCS on the M902 LS during normal operations?
• Which of the following statements about the minimum distance from Launch Stations (LSs) is correct?
• What should crew members do if they notice any irregularities during the operation checks?
• What temperature condition must be assessed before the access door is secured?
• What is the weight of a live PAC3 GM?
• Can a short measurement for roll and cross roll be conducted on the INFS?
• Before closing and securing the access door, what is verified after 5 minutes on the generator?
• Which system is responsible for verifying the integrity of the missile before launch?
• What should a GMT crane operator do if they lose sight of the signal person?
• What impact do weather conditions have on gunnery operations?
• What is checked before closing and securing the access door after the circuit breaker is closed with the lamp on?
• What is the purpose of verifying torque on the GM tie down bolt?
• What should be monitored while operating the HEMTT for efficient performance?
• What is the primary purpose of the launcher's cooling system?
• What are common indicators of system malfunctions in the 14T?
• At what maximum height should the forklift be able to lift 6000 lbs?
• Which element is considered when assessing missile accuracy?
• When unlocking torque tube handles, does CM2 rotate the plunger clockwise until it locks in place and the red shows to the right?
• What is the standard torque specification range for certain equipment operations?
• What does PMCS stand for?
• What is the size area required for GMT Reload?
• What is the significance of the "Green Light" signal in launching procedures?
• What is the purpose of the operator’s manual in operating the 14T?
• What are the three types of GMT reload methods?
• What are essential safety precautions during a firing drill?
• What is the primary purpose of the Improved North Finding System?
• When using a 30-150 lb torque wrench and a 30-36 in extension, what additional equipment is required?
• What specific info does the INFS provide to the ECS?
• Which component can indicate whether ECS is operating in local status?
• How are PAC3 MRT canisters identified?
• At what angle is the LS fully extended?
• Which interceptor is designated as an ATM2?
• What is the oil pressure range for a 10K forklift?
• What must be done immediately when a live missile hazard occurs?
• How does the cooling system affect the operation of the launcher?
• What does the term "Targeting Solution" refer to?
• What is the consequence of cranking the 15Kw generator for too long without a cooldown?
• How many crew members are required to properly emplace the TFOCA?
• What is necessary in addition to a 30-150 lb torque wrench and a 30-36 inch extension?
• What does PBIT stand for in gunnery terms?
• How is the operational range of the 14T Launcher determined?
• What does "Ballistic Trajectory" refer to in missile flight?
• Which component of the launcher needs regular inspection?
• What might happen if the launcher's maintenance schedule is not followed?
• Who is required to perform PMCS?
• Which of the following best describes the consequences of a malfunctioning cooling system?
• What is the weight of an empty PAC3 canister?
• What operational feature should be verified last before securing the access door?
• At what angle does the tilt warning alarm initiate for the HIAB 8108-2 crane?
• Which system assists in adjusting the aim of the Launcher during operations?
• What can lead to a delay in launching a missile?
• What is the maximum turning radius of the GMT crane?
• How can you determine if your INFS is operational?
• Can you conduct a short measurement for roll and cross roll on the INFS?
• How long should an engine idle before turning off the Forklift?
• Which practice ensures a successful mission outcome?
• Which two types of guidance systems are utilized in 14T missile systems?
• Which of the following responsibilities does the primary gunner have?
• How many pounds does an empty PAC3 canister weigh?
• What is the purpose of the M51 Instrument Light for the aiming circle?
• When can the access door be securely closed during generator operation?
• What is a common practice to enhance safety when guiding a vehicle driver?
• What role does a "Safety Officer" play during a live-fire exercise?
• Which reading indicates a generator's electrical condition?
• What defines a Class II leak?
• In addition to fault lamps, which indicator is critical for ensuring generator safety?
• Is stacking off-loaded canisters on top of one another considered a caution in the Drill manual?
• Is it true that LS can inadvertently slew when the PDU Motor Control unit AC is set to 'on' even if in local with the key removed?
• Why is regular inspection important for the 14T Launcher?
• What is the primary function of the 15Kw generator in gunnery operations?
• What role does mission objectives play in missile selection?
• What is the maximum time allowed for an individual to be Table IV certified?
• What is the maximum time you can crank the 15Kw generator before it must cool down?
• What should maintenance inspections primarily focus on?
• What is a key characteristic of the missiles used with the 14T Launcher?
• What is included in the procedure for conducting a system check on the 14T Launcher?
• Is the 10 series TM used to perform operator level PMCS?
• What does "NO-GO" indicate during system checks?
• What does safe operation of the 14T Launcher primarily depend on?
• What critical aspect is indicated by the graduation on the Azimuth Micrometer Scale?
• According to TC 3-01.86, what method is used for missile reload certifications during Table VIII purposes?
• How does target distance influence missile selection?
• What are the primary objectives of the Basic Gunnery course for 14T personnel?
• What should the tractor oil pressure gauge read for normal operations?
• What is the purpose of manual emplacement in gunnery?
• Is it acceptable for a reload crew to lift the rear tires of the GMT off the ground using its outriggers?
• How often should the humidity indications on stored GMs be checked?
• What is the traveling height of a forklift carrying a GM?
• When performing a jerk test, what must the AIR PRESS gauge indicate at a minimum?
• On the Azimuth Micrometer Scale, how much is each graduation equal to?
• What is the minimum time area that must be clear before returning when EOD is not required?
• What is NOT part of the verification before sealing the access door?
• On a HEMTT, which hose connects to the service coupling?
• When does the missile heat time begin?
• Is it true that the LS can inadvertently slew when PDU Motor Control unit AC is set to ON even if in local with key removed?
• Which process ensures that equipment is ready for operation based on set criteria?
• What is the first step after setting the ELES Power to ON during a PAC3 Test Launch?
• What is the significance of the Launch Table IV?
• What is the first step in preparing the launcher for engaging a target?
• What does "munition reloading" involve?
• How far should the ground rod be from the Launch Site (LS)?
• What information does the DAGR provide ECS regarding LS initialization?
• Which of the following tools is essential for torque application with the specified socket range?
• Why is mission debriefing important after an operation?
• What is the minimum distance from radar equipment required?
• How often should the Launcher software be updated?
• Describe the two main navigation systems in the 14T.
• What constitutes a Class 1 leak?
• What is the designated way to operate under limited conditions according to the Commander's authorization?
• Before implementing an operation, which aspect of equipment must be prioritized?
• What kind of data does the Command Center provide during an operation?
• Hearing protection must be worn within how many meters of the LS?
• What is the role of an assistant gunner in 14T operations?
• How many air reservoirs are located under the battery box on the HEMTT?
• Which switch must be engaged to give ECS control after LS is put in remote?
• According to the PMCS table, when is the battery gauge considered inoperative?